Could I spot some can slaw using a metal detector vs a gold ring? Even if the 2 read identical ID in meter for ID when sweeping? Hmm

You sure huh. How would you know anything about me? Stop making stupid insinuations about me please.
For the record I don’t have a therapist.
You are the one who admitted you were having trouble understanding what I was trying to explain in this thread, one of few actually. And who made you the spokesperson on this forum? Using the word US.

Actually quite the contrary, there made be some genius in what I have talked about in this thread. How does that sound?
 
Here’s target located with HF2 by a gent. He was using system shown in the guide I helped put together supplying the information. Think he was in a park. Data below and pics below taken out of his YouTube video,

Lowest MF ID = 43. There were signs of a 42 ID on some sweeps.
Highest MF ID = very steady 46.
Can slaw usually won’t behave like this. And many other lower conductive targets junk in this ID range won’t either!
Looks like gold. Has mark on the loop. Don’t know if he has tested it. Came out of the ground very clean with zero tarnish.
 

Attachments

  • IMG_1070.jpeg
    IMG_1070.jpeg
    295.5 KB · Views: 30
  • IMG_1067.jpeg
    IMG_1067.jpeg
    293.6 KB · Views: 31
  • IMG_1071.jpeg
    IMG_1071.jpeg
    145.7 KB · Views: 32
  • IMG_1073.jpeg
    IMG_1073.jpeg
    268.5 KB · Views: 33
  • IMG_1074.jpeg
    IMG_1074.jpeg
    208.6 KB · Views: 31
Last edited:
Have another report from gent I talked to on tele last night who lives in California.
He found what he thinks is a gold ring. Has the number 15 on the face of it.
He is going to acid test it.
He captured it on video.
He said it had 6 ID rise for ID. And didn’t sound very good in the highest MF. I told him the highest MF was seeing the varied conducivity caused by the numerals on the thing.
When he post video I’ll put the clips out of it here.
So folks can see.
 
Same guy who found medallion above back out today.
Using Deus 2 HF2 coil testing the dig less trash protocol.
Lowest MF = 77 ID
Highest MF = 77 ID
Turned out to be crusty zincoln. So bad it can’t even be spent likely.
These can give pretty good sounding audio. And does read in gold ring range.
 

Attachments

  • IMG_1077.jpeg
    IMG_1077.jpeg
    140.4 KB · Views: 24
  • IMG_1076.jpeg
    IMG_1076.jpeg
    143.4 KB · Views: 20
  • IMG_1079.jpeg
    IMG_1079.jpeg
    124.7 KB · Views: 21
It is wild how the coil behaves using multi frequency giving user info. Rabbit out of the hat. Huh. I have been watching videos of folks using it. And watching folks use other models. In places like parks, tot lots, sports fields. The verdict.
It’s easy to see how some could make wrong assumption using other models.
Let me give you an example.
Gent in Dallas Tx is using multi IQ detector in tot lot.
He gets a high reading signal reading around 42. He digs it it’s junk. Part of toy car or some thing. Just a foot or 2 he gets another 42 signal. What does he say in video. Oh oh here’s the other part.of the toy car. He even says he doesn’t usually dig 42 reading signals. What was the second target. A ring. Maybe stainless. You see how would hf2 done there. Would it have gave different data on each target in this example. There is good chance it would have.
Same gent sweeps his small coil under piece of equipment. He gets a 10 ID signal. He says he usually don’t dig 10 reading signals. Turns out it was a foil seal. Yeah. I got white gold ring that reads 9 using multi IQ. And hf2 coil does give info shedding light on this target has good odds of being a ring enclosure target.
I didn’t even watch this gent’s entire video. Remember those zinc Pennie’s to include the crusty ones will read high on multi IQ models and and will sound good. HF2 coil will sniff them out as high likely not ring enclosure target.
Oh yeah. I can see where HF2 coil user using the info in dig less trash guide may capitalize. More will too. So buckle up. And yes you get to dig what these folks using HF2 coil leave behind. Good luck. You’ll need it.

Let me leave folks with this thought.
Yeah. This ole hick from the sticks is very observant, I don’t have blinders on!
So what haven’t we seen really with metal detector technolgy?
Wonder if person using HF2 could make it do what it does through voice command. Hmmm
Interesting concept huh.
Wonder if I could give it a voice command to change mode/frequency.

Who knows what we will see in the future.
I would almost bet another manufacture will try to capitalize on what this HF2 coil does as it relates to what I have talked about in the this thread and what videos I have showed be it air tests or in the wild hunts.

The HF2 coil is real alright. When used with remote control, WS6, WS6 ST. I will go on here and say with this new beta version for icon X. Hf2 coil may work here on icon X as well. I may talk about this in coming days. And yes take it in the wild and show folks via video. I may suggest to Xp to actually offer icon X with HF2 coil when sold as a package if folks want to go that route with their purchase.
 
Last edited:
Don’t ask questions, just blindly agree or he goes on and on and on about finding junk and proclaiming “ I called it” 🤣
Don't say that TNs thread approaching a thread started by a very pretty woman who used to post here... its amazing how many posted on that thread in short order lol... don't go looking for it, you won't find it and I am not bringing it back up :lol:
 
Gent back in park using HF2. He’s calling targets for ring enclosure status digging all targets.
Gent comes upon a gold ring ID range signal.
Target read 70 ID Lowest MF.
Target read 65 ID Highest MF.
This is not how a ring enclosure target typically behaves.
The target was dug. And was lead.
 

Attachments

  • IMG_1087.jpeg
    IMG_1087.jpeg
    169.1 KB · Views: 17
  • IMG_1086.jpeg
    IMG_1086.jpeg
    156.5 KB · Views: 21
  • IMG_1088.jpeg
    IMG_1088.jpeg
    103.6 KB · Views: 19
Last edited:
Same gent still in park,
Get signal on target reads 60 using Lowest MF.
Target reads 63 Highest MF.
This is how many nickels can behave yielding 3 points ID rise. Granted some nickels can read 61, 62, 63 and still yield this 3 ID points rise.
Target was dug. It was a nickel.
 

Attachments

  • IMG_1082.jpeg
    IMG_1082.jpeg
    163.1 KB · Views: 20
  • IMG_1085.jpeg
    IMG_1085.jpeg
    94 KB · Views: 21
  • IMG_1081.jpeg
    IMG_1081.jpeg
    164 KB · Views: 19
Last edited:
Same gent still in the park.
Gent comes upon a gold ring range ID signal.
Signal on target reads 77 ID using Lowest MF.
Signal on target reads 70 ID using Highest MF
This is not how a ring enclosure target typically behaves,
Target dug = melted lead.
 

Attachments

  • IMG_1089.jpeg
    IMG_1089.jpeg
    163.9 KB · Views: 17
  • IMG_1090.jpeg
    IMG_1090.jpeg
    165.6 KB · Views: 17
  • IMG_1092.jpeg
    IMG_1092.jpeg
    77.7 KB · Views: 15
Here’s airtest of one of those foil seals like could be found on a container and a white gold 10k ring.
These 2 targets read identical using lowest and highest MF. Both read close to the bottom of gold ring range.
Use of highest single freq (120khz) does expose the ring. I have seen this behavior in the wild using hf2 coil in parks. I actually dug this foil seal and called it non ring enclosure target.
ID values are as follows. The pics are sorta blurry video was shot in the rain.
10 K ring.
Lowest MF ID = 40
Highest MF ID = 42
Highest single freq 120 kHz ID = 43

The Foil Seal
Lowest MF ID = 40
Highest MF ID = 42
Highest single freq 120 kHz ID = 40
Notice the seal reads identical ID wise using Lowest MF compared to highest single freq 120 kHz unlike the the 10k white gold ring does.
 

Attachments

  • IMG_1095.jpeg
    IMG_1095.jpeg
    131.3 KB · Views: 18
  • IMG_1094.jpeg
    IMG_1094.jpeg
    160.1 KB · Views: 19
  • IMG_1093.jpeg
    IMG_1093.jpeg
    141.1 KB · Views: 19
  • IMG_1096.jpeg
    IMG_1096.jpeg
    141.4 KB · Views: 20
  • IMG_1097.jpeg
    IMG_1097.jpeg
    150 KB · Views: 15
  • IMG_1098.jpeg
    IMG_1098.jpeg
    170.6 KB · Views: 21
  • IMG_1101.jpeg
    IMG_1101.jpeg
    167.6 KB · Views: 14
  • IMG_1100.jpeg
    IMG_1100.jpeg
    115.2 KB · Views: 21
Don't say that TNs thread approaching a thread started by a very pretty woman who used to post here... its amazing how many posted on that thread in short order lol... don't go looking for it, you won't find it and I am not bringing it back up :lol:
There is a big difference, in that enormous thread you mentioned, the majority of the posts weren't her's.
 
Yes, the method "works", but it has serious limitations. More importantly, we have no evidence that it actually works any better than the other methods we already use to find rings...and that's a pretty damn important thing to know!

In addition, the method doesn't reliably distinguish pull tabs from rings, and pull tabs are one of the biggest hindrances to finding rings in parks. Then of course, there are all the false negatives of the method to consider.

Posting that someone found a ring using the method is not proof that the method is effective, because there's no way of knowing whether that same ring would have been found using conventional methods. Finding a ring while using a particular method doesn't establish that the method was responsible for finding it. There's also the question of how many rings or other jewelery (becuase the method only works on closed loop) are passed over because they didn't produce the desired ID change.

Even if the method reduces the amount of trash being dug, that doesn't necessarily mean it results in finding more rings. It could simply mean fewer holes being dug, while potentially passing over rings and jewelry that don't produce the wanted ID change.

In addition, it could even be found that digging only mid conductors while notching out pull tabs could produce more gold rings than using this method. We simply don't know, because no proper comparison has been done.

A proper test would involve checking a large number of unknown targets with the method, at avarious depths and orientations, recording which ones pass and fail the frequency test, and then digging every single target, including those the method says to reject. That would establish the percentage of gold rings and gold jewelry the method correctly identifies, the percentage it misses, and how much trash it actually eliminates. The results would also need to be compared with conventional ring finding methods.

Until someone does a proper comparison with conventional methods, I don't see how anyone can claim this method is more effective at finding rings. It might be, but it might also be less effective. Right now, I don't think we have the proper evidence to say one way or the other.
 
I have dug hundreds of targets in parks reading in gold ring range. A super high percentage of them failed for ring enclosure. And none of the failures were stand alone rings. None.
This system seems to work.
Quite a few of these same failure targets yielded grand tonal nuance too. Still they failed the ID test parameters. And were not stand alone ring enclosure targets.
Airtest results mirror this above. Plus other models were compared. All other models Multi freq models, users are stuck digging a lot of these junk targets,
Common sense tells the more junk that can be dismissed would mean the more time a user has during their detecting outing to get coil over a ring enclosure behaving target.

If we equate this to using machines looking for high conducive coins and silver rings.
Is the person out there going to find and dig more higher conductive coins and silver rings digging all the nonferrous range or all they going to find more digging based on ID. I,e, using even Etrac, CTX, Deus 2, Equinox, Manticore, Legend , Legend 2. The tremendous ID capabilities these MF detectors have on higher conductors even on deeper ones leads to the users success. Right?
There will always be one off somewhere, but what would be the typical trend numbers wise for their success per hour of detecting in modern trash sites. I think I know the answer. As I have used vlf detectors Mukti freq looking for higher conductive in trashier sites.

It’s called letting the detector do the work.
And in this thread it’s called letting the hf2 do the work.

Many find this system helpful.
And I have provided clear evidence via video.

You should use the HF2 coil and and compare it to your Legend. And watch what happens. You don’t have clue a target under your Legend’s coil is ring encloser Design or not.

This is not about which detector or coil is the better Locator. Many detector will locate a gold ring. Bud does the user know or have an idea of what’s under their coil really? Besides it reads in gold ring range.

In closing here.
Where are the videos where other models multi freq are being used. And the user is calling the gold ring range ID signal target a ring or not. Like I have done sweeping hundreds of gold ring ID target signals.
Where are the videos?
Notice the sharpshooter didn’t do this with equinox or manticore or Etrac or CTX or Legend, triple score did he. Why you reckon?
 
Last edited:
None of this “method” makes any sense at all. If you dismiss pull tabs and lead you’re missing gold. Period. No hocus pocus mumbo jumbo talk changes that, and the D2 is no better than a Manticore, NOX or or Legend in finding gold rings. Fact this method doesn’t do sheet
 
HF2 coil will behave loads different on lead vs gold ring. Loads!
From ID perspective.
Crusty Zincoln penny too.!

In all likelikelyhood users user other models besides Deus 2 and HF2 coil. They would have to dig every 4” deep crusty zincoln penny thinking it might be a gold ring. With HF2 coil I can check and walk off of it, having a pretty good idea it’s not a gold ring or a platinum ring, I can say also it’s not a pull ring solo or a square tab. How about that.

That’s my story and I am sticking to it.
Why
Because it’s the TRUTH!

Why did I start talking about this.
What..
I woke one morning after a dream I had.
And thought I would just post a bunch of bs,
Knowing full well others out there have the equipment. Hmmm
If this was bs it would have have been shot down by actual other users by now.,
It hasn’t been shot down.
She’s flying. And FLYING HiGH !
And I am getting some good reports by users.
Some I have shared in this thread.
 
Last edited:
Back
Top Bottom