Friendly Metal Detecting Forums

Friendly Metal Detecting Forums (https://metaldetectingforum.com/index.php)
-   Make It or Fix It Yourself (https://metaldetectingforum.com/forumdisplay.php?f=21)
-   -   Equinox coil ear stiffener and repair (https://metaldetectingforum.com/showthread.php?t=277780)

ChrisMD 01-08-2020 05:37 PM

For those waiting on some coil ears I had a couple day delay because all my filament got water logged with the humid summer. I just got an order of filament in and they are starting to roll off now, will start mailing tomorrow. https://uploads.tapatalk-cdn.com/202...5faaa4ce39.jpg


Sent from my iPhone using Tapatalk

Dan B. 01-08-2020 06:44 PM

I had my local library print one for me. It's white. Can they be spray-painted without affecting the coil?

ChrisMD 01-08-2020 08:18 PM

Could you do me a favor and ask your buddy what Slicer he used to slice the file? I've tried using two different slicer and the regular reinforced model falls apart when I slice it. The repair model slices and prints fine.

Thanks.

Quote:

Originally Posted by ToySoldier (Post 3173931)
Picked mine up last night from a buddy with a 3D printer. Clever design, perfect fit, and clearly does what it's designed to do. The original bolt is just long enough that the nut turns and tightens enough that I'm not worried about it backing itself off.


castleberry 01-09-2020 04:56 PM

ChrisMD, PM sent with address .. let me know if you don't see it..

Very Grateful for the help man

Brian

Dan B. 01-11-2020 05:30 PM

1 Attachment(s)
I went back to my local library today, and had them print me a 3D ear stiffener for my 6-inch coil with the program they save the last time I was there. They did a good job it fits perfect and it only cost me $1.

Once again here is the link to the 3D blueprints.

https://www.thingiverse.com/thing:3949618

ChrisMD 01-11-2020 05:33 PM

Quote:

Originally Posted by Dan B. (Post 3182125)
I had my local library print one for me. It's white. Can they be spray-painted without affecting the coil?



For some reason I missed this. Yeah, you can spray it with acrylic no problem.


Sent from my iPhone using Tapatalk

Dan B. 01-12-2020 02:01 PM

Quote:

Originally Posted by ChrisMD (Post 3182796)
For some reason I missed this. Yeah, you can spray it with acrylic no problem.


Sent from my iPhone using Tapatalk

Thanks chirs!!!

castleberry 01-13-2020 04:36 PM

2 Attachment(s)
Look what arrived in my mailbox today down here in TN...

ChrisMD, you sir are a gentleman and a asset to the forum, thanks to you I am back in action and can resume a few hunts I have scheduled till such time I can then return my coil to ML for replacement. Then Im armed to protect the new coil from the same scenario ...

:urock: ChrisMD

Sincerely

Brian AKA castleberry

tnsharpshooter 01-13-2020 06:13 PM

Quote:

Originally Posted by castleberry (Post 3183429)
Look what arrived in my mailbox today down here in TN...

ChrisMD, you sir are a gentleman and a asset to the forum, thanks to you I am back in action and can resume a few hunts I have scheduled till such time I can then return my coil to ML for replacement. Then Im armed to protect the new coil from the same scenario ...

:urock: ChrisMD

Sincerely

Brian AKA castleberry

Got mine today.
Super dude this gent Chris.
Thanks Chris.

ToySoldier 01-13-2020 07:41 PM

Quote:

Originally Posted by ChrisMD (Post 3182154)
Could you do me a favor and ask your buddy what Slicer he used to slice the file? I've tried using two different slicer and the regular reinforced model falls apart when I slice it. The repair model slices and prints fine.

Thanks.

Hope you got your issue fixed. My buddy has been aloof lately. I was also going to give him a few bucks to make me one for the 6" coil, although I'm a lot less concerned about that one getting broken.

ChrisMD 01-13-2020 07:48 PM

Quote:

Originally Posted by ToySoldier (Post 3183485)
Hope you got your issue fixed. My buddy has been aloof lately. I was also going to give him a few bucks to make me one for the 6" coil, although I'm a lot less concerned about that one getting broken.

I did get it sorted out, the model only worked in one particular slicer, which is the software package that chops up the model and sends it to the printer. I hate using that slicer that ended up working though, so I just jumped on CAD with my limited skills and fixed the model well enough to print.

ChrisMD 01-13-2020 08:32 PM

Thanks fellas, glad it worked for ya and you like it.

I had a bunch of new requests come in, for those still waiting I filled up all my printers making Star Wars Death Troopers for all the kids coming to my sonís birthday party. As soon as this batch comes off Iíll free up a printer to make another batch, should have them out by Wednesday.

https://www.myminifactory.com/object...-trooper-32710

Quote:

Originally Posted by castleberry (Post 3183429)
Look what arrived in my mailbox today down here in TN...

ChrisMD, you sir are a gentleman and a asset to the forum, thanks to you I am back in action and can resume a few hunts I have scheduled till such time I can then return my coil to ML for replacement. Then Im armed to protect the new coil from the same scenario ...

:urock: ChrisMD

Sincerely

Brian AKA castleberry

Quote:

Originally Posted by tnsharpshooter (Post 3183460)
Got mine today.
Super dude this gent Chris.
Thanks Chris.


WildDigger 01-14-2020 05:54 PM

Glad I remembered this here. Thanks again for making the file available to all. My nephew told me his buddy has a 3D printer so he is going to get him to make me a few.

Dan B. 01-14-2020 07:53 PM

Quote:

Originally Posted by WildDigger (Post 3183811)
Glad I remembered this here. Thanks again for making the file available to all. My nephew told me his buddy has a 3D printer so he is going to get him to make me a few.

No problem always glad to be of some help.

penneyrich 01-21-2020 10:28 PM

I just purchased a 15" coil for my Nox 600. I had a friend print me one for each coil (6", 11", 15"). The stiffener fit perfectly on the 6" and 11". The stiffener ear slots were too narrow for the 15". I noticed that the ears on the 15" coil taper outward whereas the 6" and 11" coil ears were the same dimension along the entire ear. All of the information that I have read about the stiffeners says that the 11" and 15" stiffeners fit the same. Has Minelab changed the ear design to fix this issue or is there a different program for the 15" coil yoke stiffener? Thanks for any help given!!

Dan B. 01-22-2020 04:05 PM

Quote:

Originally Posted by penneyrich (Post 3186027)
I just purchased a 15" coil for my Nox 600. I had a friend print me one for each coil (6", 11", 15"). The stiffener fit perfectly on the 6" and 11". The stiffener ear slots were too narrow for the 15". I noticed that the ears on the 15" coil taper outward whereas the 6" and 11" coil ears were the same dimension along the entire ear. All of the information that I have read about the stiffeners says that the 11" and 15" stiffeners fit the same. Has Minelab changed the ear design to fix this issue or is there a different program for the 15" coil yoke stiffener? Thanks for any help given!!

Maybe you can take a small flat file and open that up a little bit to get it to work. Here is the link to where the program was. Read the comments one of the comments show someone else had an issue. Updated links here also.

https://www.thingiverse.com/thing:3949618/comments

Charly-in-CT-RI 01-23-2020 08:17 PM

Quote:

Originally Posted by penneyrich (Post 3186027)
I just purchased a 15" coil for my Nox 600. I had a friend print me one for each coil (6", 11", 15"). The stiffener fit perfectly on the 6" and 11". The stiffener ear slots were too narrow for the 15". I noticed that the ears on the 15" coil taper outward whereas the 6" and 11" coil ears were the same dimension along the entire ear. All of the information that I have read about the stiffeners says that the 11" and 15" stiffeners fit the same. Has Minelab changed the ear design to fix this issue or is there a different program for the 15" coil yoke stiffener? Thanks for any help given!!

My 11 and 15 are not the same. I purchase one from someone and the forum and it was said they are the same by mine were not.

ChrisMD 01-23-2020 08:38 PM

Quote:

Originally Posted by Dan B. (Post 3186227)
Maybe you can take a small flat file and open that up a little bit to get it to work. Here is the link to where the program was. Read the comments one of the comments show someone else had an issue. Updated links here also.



https://www.thingiverse.com/thing:3949618/comments



The comments were actually from me about having issues. The modelís mesh was messed up and would only work in a specific program that I hate using.

I repaired the model, and in my case the same model works for both my 11 and 15 coil.


Sent from my iPhone using Tapatalk

ChrisMD 01-23-2020 08:41 PM

Quote:

Originally Posted by penneyrich (Post 3186027)
I just purchased a 15" coil for my Nox 600. I had a friend print me one for each coil (6", 11", 15"). The stiffener fit perfectly on the 6" and 11". The stiffener ear slots were too narrow for the 15". I noticed that the ears on the 15" coil taper outward whereas the 6" and 11" coil ears were the same dimension along the entire ear. All of the information that I have read about the stiffeners says that the 11" and 15" stiffeners fit the same. Has Minelab changed the ear design to fix this issue or is there a different program for the 15" coil yoke stiffener? Thanks for any help given!!



In my case, the same model works for the 11 and 15 for me but I had to fix the model in order to get it to print. There are more than one version of coil support models floating around out there also. The other thing is the tolerances are tighter on the 15, if your buddies printer isnít calibrated for dimensions properly that tight tolerance can make the print a no-go.


Sent from my iPhone using Tapatalk

btripp6 01-28-2020 02:43 PM

Quote:

Originally Posted by ChrisMD (Post 3181213)
Donít pay $15, itís like 2 cents worth of plastic and 5 cents of electric. If you want let me know what color you like and how many you want for which coils and Iíll send them to you.

How much would you charge me to make 6 of them? I will gladly Paypal you for them.


All times are GMT -4. The time now is 02:10 PM.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.