I had a couple of hours to detect today after another mini blizzard. I decided to stay close to home and hunt next to a curb at a local park that I have hunted with Deus 1 and the Equinox 800 in the past. The area I was hunting is absolutely loaded with aluminum trash and steel crown bottle caps with various states of rust unless they are recent drops. Very iron mineralized ground on top of the thousands of trash targets.
Knowing this in advance I was thankful that I have the Deus 2 (and the Legend and Equinox 900) which do not have half of the regularly found aluminum pull tabs ID's landing right on top of the most common gold ring target IDs and the US nickel target IDs (like the Equinox 600/800/Vanquish models) both of which I really enjoy digging.
In the past I have tried Deus 1 at places like this and quickly became super frustrated with all of the silver target ID range responses that could easily be US copper pennies, clad dimes clad quarters, silver coins and silver jewelry but instead were lowly pull tabs and bits of aluminum along with steel crown bottle caps that were showing up in the upper 80s to upper 90s target ID range due to severe up averaging if they were deeper than 3" or so in this iron rich dirt.
Deus 2 using its multi modes based on the Fast program simply does not do that to all of that aluminum and steel trash unless it is right at the edge of detection in the dirt around here, so I had no hesitation picking it for detecting this super trashed area.
I was using a saved program based on Sensitive, with 5 tones Square Wave audio, disc on 10, iron audio ON, reactivity 2, Silencer 1, bottle cap reject 1 and sensitivity on 95. Deus 2 was a bit jittery but consistent which is how I like it. The US nickel medium pitched tone was set up to sound on target IDs between 59 and 63. The highest tone for clad dimes and up was set 90 to 99.
So, I concentrated on the gold and silver range of target IDs specifically any good sounding target with a consistent ID of 59 to 63 and any target with a consistent target ID of 90 and above and was basically cherry picking for US nickels/medium sized gold rings and US coins above zinc pennies with any silver thrown in.
The 1.9 gram 10K ring had a target ID of 62/63 just like the nickels and square tabs in the photo. These targets were in the 3 to 6" depth range.
There has been a lot of chatter about using single frequencies for detecting and how they are just "better" especially in reference to the new Minelab X-Terra Pro. Theoretically and in certain very mild soil conditions that is good advice. Where I most often detect......absolutely not good advice.
I deliberately checked the target IDs of each of the low to mid conductor targets in the bottom half of the paper plate photo before digging them. I used default Deus 2 Mono set on 17 kHz. All of those targets which are normally 59 to 66 had target IDs above 85.
I'm very happy to use Deus 2 FMF simultaneous multi frequency tech, that's for sure since I can at least call the non-ferrous conductivity of targets before I dig them for the most part.
Thanks for reading.
Knowing this in advance I was thankful that I have the Deus 2 (and the Legend and Equinox 900) which do not have half of the regularly found aluminum pull tabs ID's landing right on top of the most common gold ring target IDs and the US nickel target IDs (like the Equinox 600/800/Vanquish models) both of which I really enjoy digging.
In the past I have tried Deus 1 at places like this and quickly became super frustrated with all of the silver target ID range responses that could easily be US copper pennies, clad dimes clad quarters, silver coins and silver jewelry but instead were lowly pull tabs and bits of aluminum along with steel crown bottle caps that were showing up in the upper 80s to upper 90s target ID range due to severe up averaging if they were deeper than 3" or so in this iron rich dirt.
Deus 2 using its multi modes based on the Fast program simply does not do that to all of that aluminum and steel trash unless it is right at the edge of detection in the dirt around here, so I had no hesitation picking it for detecting this super trashed area.
I was using a saved program based on Sensitive, with 5 tones Square Wave audio, disc on 10, iron audio ON, reactivity 2, Silencer 1, bottle cap reject 1 and sensitivity on 95. Deus 2 was a bit jittery but consistent which is how I like it. The US nickel medium pitched tone was set up to sound on target IDs between 59 and 63. The highest tone for clad dimes and up was set 90 to 99.
So, I concentrated on the gold and silver range of target IDs specifically any good sounding target with a consistent ID of 59 to 63 and any target with a consistent target ID of 90 and above and was basically cherry picking for US nickels/medium sized gold rings and US coins above zinc pennies with any silver thrown in.
The 1.9 gram 10K ring had a target ID of 62/63 just like the nickels and square tabs in the photo. These targets were in the 3 to 6" depth range.
There has been a lot of chatter about using single frequencies for detecting and how they are just "better" especially in reference to the new Minelab X-Terra Pro. Theoretically and in certain very mild soil conditions that is good advice. Where I most often detect......absolutely not good advice.
I deliberately checked the target IDs of each of the low to mid conductor targets in the bottom half of the paper plate photo before digging them. I used default Deus 2 Mono set on 17 kHz. All of those targets which are normally 59 to 66 had target IDs above 85.
I'm very happy to use Deus 2 FMF simultaneous multi frequency tech, that's for sure since I can at least call the non-ferrous conductivity of targets before I dig them for the most part.
Thanks for reading.
Last edited:
